I have a a failed horn switch on my Sport.
It is sort of intermittent insofaras I did get one short toot by wiggling it but no more.
I have acquired...
Last post
Ah, great. Quite a good photo sequence of Series1 binnacle switch gear disassembly on 13.8 to 13.9.
Will have a go in next round of daylight! 😂
Could anyone who runs a petrol BX advise if is best / ok to run on standard unleaded or standard unleaded with an additive or super unleaded please?...
Last post
Thanks for reply . I can get super unleaded where I live here so I'll go with that
Hi everyone, as the title states, I'm having a bit of trouble with my diesel rev counter & I'd appreciate some advice on it.
It has been reading...
Last post
Here's one sensor I've found, which I believe is most like the original, although the plug is different. I'm not worried about that as my BX lost its...
Hey all.
I've been having an issue with my BX that has finally gotten on top of my nerves. Namely there is this annoying ticking/static noise coming...
Last post
The cables do wear and get noisy and the speedo head can do likewise too. Have you tried disconnecting the cable at the speedo end for diagnosis...
Hi. Trying to find out why nothing electrical on my hatchback boot lid works.
Thought might be an earth problem so tried taking numberplate light...
Last post
Finally got to the bottom of this and solution was really simple.
As Jaba says the wires run flat along floor to back of car, they run all the way to...
Since one of the front struts on our GTI is leaking badly and I have obtained a good second hand one I am planning to swap them tomorrow.
Can anyone...
Last post
Silly question - how do you know it is leaking badly? Does the LHM go anywhere but back to the tank via the strut returns when the strut is tired? (I...
Investigation of a clunk on my BX 4x4 estate revealed the middle subframe bolt, UK offside - that's the forward of the pair of bolts that pass...
Last post
The subframe bolts are the same on the 2wd & the 4x4, or at least on the mk2 cars, so one should be easy enough to acquire. I’d personally remove the...
I rebuilt my BX gearbox back in June, with all new bearings & seals. The car has done...
Last post
If you have rebuilt a gearbox you are more skilled than I but the mention of GL4 and sychro problems really screams out to me as on my other car love...
Good morning everyone, I'm Riccardo and I live in Piacenza, Italy. I recently saved a white BX break 19 TZS from the wrecker, but it will require a...
Last post
When I had a white estate the trim was definitely black in a satin or matt finish. I used a spraycan matt black when it needed some renovating.
Thats...
Hey all!
I am once again asking for some advice on behalf of a friend. This time its about the plastic trim/cladding in the boot. They removed all...
Last post
They’re a bit tricky & fiddly to remove without damaging anything. You actually need to remove the C pillar plastic cover first, it’s held on with 2...
Good evening fellow BXers. Question regarding my 1993 BX 1.9d with the BE1 gearbox. There is up and down movement/play on the clutch fork which comes...
Last post
From what you say I reckon you have a problem with the forked lever bush. It should fit securely to a ball joint which is part of the gearbox...
Hello everyone!
So this is an unusual post for me, as I'm asking for a friend. His BX is a 1984 BX 14. The problem we're having is that he can't get...
Last post
Push the door card in, and also the contacting plastic ring. This should reveal a pin through the spindle. Push it out and don`t loose it, then...
This has now arrived and planning on doing this shortly. Some sites mention a rubber seal that goes on the end between pipe and caliper. Chevronics...
Last post
1) Unfortunately, no, all BX vehicles use the rubber seal. They’re not like conventional vehicles, so there’s a rubber seal between the unions, it’s...
Hi. I am desperately in need of a top hose for my BX19GTI 8 valve. I can’t source one in New Zealand where I live and I’ve looked on just about every...
Last post
This might be for your GTi depending on RP number:
Alternatively your best bet might be to investigate making up a substiute hose in silicone or...
Does anyone have a definitive diagram, pictures perhaps, of the LHM pipes on the rear suspension of a BX please? The Y piece on the right hand side...
Last post
Interesting, Ive seen green ones and the one that disintegrated appeared to be black. We found that the fuel hose we used is of too small a diameter...
Can anyone remind me of where to the colour codes for Mk1 BX Bumpers please! Ive looked and looked but cant see it, My car is romantic blue, but the...
Last post
Mine does as well. Also when main dealer enters the VIN directy off my V5 it shows VIN invalid. I think Citroen have been doing some house keeping on...
I have a BX estate, referred to at times as the red shed - not a thing of beauty but has been stopping, starting, going forward/back/up/down for more...
Last post
If it’s only apparent on high setting that would indicate it’s the brake line, as the rear brakes are only under full pressure when there is heavy...
Hi, does anyone knoe what other cars wheels will fit straight on a BX as I want to fit some nice alloys to my estate? Also how much and where could I...
Last post
I don't want to start a new topic for this so decided to bump this one...
Does anyone know if it's possible to fit 13 rims on a base model BX14?...
I got CITROEN BX 1.6 of 1987 model with 171 engine and automatic transmission last month. Knocking noise occurs when accelerating. I think one of the...
Last post
Thanks, Jaba! I found the timing plate by removing the air cleaner box. Using strobe light, I could read the advancing angle befor TDC....
Hey all!
I have a quick question about my HP pump. I recently had the pressure regulator rebuilt, so that is no longer causing issues. However, there...
Last post
Yes sounds like Yr H. P pump is struggling to maintain pressure, no PAS on cold starts is indicative of this, also worth checking that your...
Hi all,
I have tzd bx with xud7te engine, cambelt skipped camshaft and cam caps broke off so i need new head, i have a cheap engine oportunity but...
Last post
Not sure on that, but if you can source an xud9 bx 1.9n/a camshaft you can use it on an XUD7TE head, it just makes it more torquey at lower rpm's but...
Hi there, I've driven my 16TRS auto just once, 100 miles back from Hertfordshire and it's been sitting in my lockup for just over a fortnight. It was...
Last post
Many thanks. Very sorry for the delay in getting back to you but your words are very useful. I've found that it just needs a very firm pull and my...
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
