BX Technical

4931 topics

Page 2 of 99
- Jump to page:
Previous
1
2
3
4
5
…
99
Next

Most liked posts	Author	Posted	Liked	Forum
Window crank removal	thorter	Fri Sep 29, 2023 9:32 am	2 times in total	BX Technical
changing a front strut	Jaba	Sat Sep 16, 2023 7:57 pm	2 times this year	BX Technical

Topics

Replies

Views

Last post

BX advice requested from Canada

Last post by BXTASY « Thu Oct 27, 2022 5:18 pm
Replies: 8
by Canada's only BX » Sun Jun 26, 2022 3:33 pm

First post

Hi: as far as I know I own the only BX in Canada, a 1991 Millésime 1.6 5-spd, w/PAS; no A/C and 110,000 Kms (68,500 miles). It was sold in France and...

Last post

Welcome to the not-yet-active BX Club North America, just now invented. I know of nine BX models in the US, three here in north Texas. Two are at the...

8 Replies

3352 Views

Last post by BXTASY
Thu Oct 27, 2022 5:18 pm
New Member Cannot Believe I'm Thinking of BXs Again

Last post by rutter123 « Tue Oct 18, 2022 10:00 am
Replies: 6
by tobytronic » Sun Oct 16, 2022 11:51 pm

First post

Thanks for accepting me. I started working on Citroens in 1984 at A&J White Blackburn. Then i went to John Heyworth Nelson, where I eventually became...

Last post

Do it. Save one from its fate, think prices have topped out for the nicest examples, but still plenty of choice for reasonable £s if you gonna DIY.

6 Replies

3492 Views

Last post by rutter123
Tue Oct 18, 2022 10:00 am
Fuel pump replacement, gasket and spacer

Last post by NeilGP « Tue Aug 23, 2022 7:24 pm
Replies: 8
by Jugostran » Wed Aug 10, 2022 2:44 pm

First post

Hey all.
So, recently I found an ad for a BX fuel pump and gasket. Lucky that considering that my fuel pump gasket is leaking. However, I quickly ran...

Last post

In the mechanical pump the gasket goes between the spacer and the cylinder head

8 Replies

6953 Views

Last post by NeilGP
Tue Aug 23, 2022 7:24 pm
Rumble noise and sharp metallic sound

Last post by David « Tue Aug 16, 2022 10:55 pm
Replies: 5
by SeanScot » Sat Aug 06, 2022 8:35 pm

First post

Hi folks

There’s a rumbling noise on our 87 19RD that I wonder is wheel bearings but sounds a metallic clatter coming from rear passenger side that...

Last post

It's difficult to say without seeing the car, but from your description, I think that it could be the wheel bearing. It's possible that the bearing...

5 Replies

2878 Views

Last post by David
Tue Aug 16, 2022 10:55 pm
How to quieten a noisy exhaust?

Last post by David « Tue Aug 16, 2022 10:37 pm
Replies: 14
by deltic » Sun Jun 26, 2022 6:15 pm

First post

As posted elsewhere I recently had a stainless steel exhaust system fitted to the BX which unfortunately I find uncomfortably noisy. Indeed it is...

Last post

I've been persevering with mine & I've realised that if I keep the engine revs down, keep the back seats up & if the radio is on, then I can't really...

14 Replies

8918 Views

Last post by David
Tue Aug 16, 2022 10:37 pm
Interference Engines

Last post by Jaba « Wed Aug 10, 2022 9:33 am
Replies: 4
by bx16trs » Mon Aug 08, 2022 12:38 pm

First post

Hi all, been trying to find out whether the engine in my 1986 BX16TRS is interference or non-interference? None of the web refs I Googled show...

Last post

Correct me if I'm wrong, years ago I had a mk1 vauxhall astra 1300 cambelt snapped due to seized water pump
No valve or cam damage, new belt and pump...

4 Replies

3255 Views

Last post by Jaba
Wed Aug 10, 2022 9:33 am
Using a 405 Electric Mirror To Make a BX Electric Mirror?

Last post by krekov « Wed Aug 03, 2022 12:26 pm
Replies: 2
by krekov » Sat Jun 25, 2022 12:02 pm

First post

Hello,
I've been wondering if it's possible to convert a manual BX mirror into an electric one using the guts of a Pug 405 mirror, the mk 1.
Anyone...

Last post

Welp, it took a while but I've reached a conclusion: the electric mirror mechanism for the passenger side (on LHD cars) is exactly the same as the...

2 Replies

2200 Views

Last post by krekov
Wed Aug 03, 2022 12:26 pm
Fitting A/C to a BX 16

Last post by Jugostran « Sun Jul 24, 2022 11:40 am
Replies: 5
by Jugostran » Sat Jul 16, 2022 5:47 pm

First post

Hey all!
So, it has been more than a year since I got my BX. I love it so far. Yes, it is still quite broken, but it is endearing. However, since...

Last post

Hi there, I'm fitting a/c to my MK1 GT and can confirm it is a fair amount of work, the hardest part is likely to be finding the parts and then...

5 Replies

2920 Views

Last post by Jugostran
Sun Jul 24, 2022 11:40 am
What carburetor model does the XU5 2C engine have?

Last post by Jugostran « Fri Jul 15, 2022 11:48 am
Replies: 4
by Jugostran » Wed Mar 16, 2022 9:58 am

First post

Hey all!
So, I am getting ready to rebuild the Solex carburetor in my early 1989 BX 16 TRS. Trouble is, I don't know the exact model of the...

Last post

If it is Solex and the engine is the type 171Z engine, then it could also be the 34-34-Z1 PSA 464. BUT, the factory is well known for making...

4 Replies

3587 Views

Last post by Jugostran
Fri Jul 15, 2022 11:48 am
Another diesel starting thread.

Last post by Dave_16v « Fri Jul 08, 2022 7:33 am
Replies: 29
by saintjamesy89 » Tue Oct 08, 2013 6:09 pm
1

2
First post

Hi guys, had a bit of a time trying to start the TXD turbo these last few mornings. Once, I could put down to it just being a BX, but twice is too...

Last post

Quite possibly a stuck stop solenoid, it open and closes with on /off as power goes to it. Sometimes giving it a tap may free it.

Edit

After a bit...
29 Replies

7110 Views

Last post by Dave_16v
Fri Jul 08, 2022 7:33 am
Speedo cable

Last post by Canada's only BX « Thu Jun 30, 2022 9:05 pm
Replies: 8
by FroggyBX » Mon Apr 19, 2021 12:23 pm

First post

I've noticed a slight clicking when pottering along (I'm retired in France). I think it may be something to do with the speedo cable. Checked the...

Last post

A company in Italy has quite a few items for the BX and all other Citroen, going back to the 15s, including speedo cables

Pimax Srl (

Look for the...

8 Replies

2029 Views

Last post by Canada's only BX
Thu Jun 30, 2022 9:05 pm
Should I take the windshield off, yes or no?

Last post by Benfatto « Mon Jun 27, 2022 8:43 pm
Replies: 4
by Benfatto » Sat Jun 25, 2022 3:17 pm

First post

BX forum 5.jpg

The owner before last parked it under a tree for years. The rust did not look so bad at first, but after cleaning I discovered a...

Last post

Thank you for all your replies! I 'll bite the bullet then and take it off, weld and paint it. Probably have it re-placed by a professional, since...

4 Replies

1658 Views

Last post by Benfatto
Mon Jun 27, 2022 8:43 pm
Abs light, bleeding?

Last post by womble3go « Mon May 16, 2022 9:34 pm
Replies: 5
by womble3go » Sun May 15, 2022 3:00 pm

First post

Hi all,
Ive just done some work on my hydraulic system, changed the FDV and regulator had all 5 spheres off and checked and cleaned the tank and...

Last post

I will check my spare one just to make sure that its ok, but at least no one is say to bleed the brake which was a pain last time I did it.

Thank...

5 Replies

3422 Views

Last post by womble3go
Mon May 16, 2022 9:34 pm
Replacing a headlight

Last post by deltic « Fri May 06, 2022 9:49 pm
Replies: 2
by deltic » Fri May 06, 2022 2:36 pm

First post

Am I correct in thinking that by doing a straight swap of a headlight that the adjusters will remain in position and that the new headlight will be...

Last post

And thank you for shedding light on my question!

2 Replies

1518 Views

Last post by deltic
Fri May 06, 2022 9:49 pm
TZI valve clearances

Last post by rhysaccess « Fri Apr 22, 2022 1:30 am
Replies: 4
by rhysaccess » Mon Apr 18, 2022 3:32 pm

First post

Howdy all,

While checking valve clearances on my DKZ engine, I've used the 159 specs in one of my Haynes manuals of 0.15 - 0.25 Inlet & 0.35 - 0.45...

Last post

Yes, the vagaries of chasing down some exact numbers by shimming are not new to me. If I’m to use the “standard” BX19 clearances – just three exhaust...

4 Replies

1690 Views

Last post by rhysaccess
Fri Apr 22, 2022 1:30 am
Replacing the BE3 gearbox

Last post by rhysaccess « Fri Apr 08, 2022 8:11 am
Replies: 7
by rhysaccess » Sun Apr 03, 2022 11:47 am

First post

Howdy all,

With the planet gears breaking through the gearbox bell housing - the original BE3 CJ47 gearbox is to be replaced.

I have a 20TE47 unit...

Last post

Based on the (excellent) feedback here - I’ve ordered the appropriate bits, and I await the (hopefully correct) parts to arrive at my door....

7 Replies

2345 Views

Last post by rhysaccess
Fri Apr 08, 2022 8:11 am
Removing a BX16v alternator

Last post by szhrr5cc « Tue Apr 05, 2022 10:46 pm
Replies: 2
by szhrr5cc » Tue Apr 05, 2022 2:18 pm

First post

Hello All, working on our 16v to remove the alternator as it very noisy and either needs replacing or rebuilding. We have freed it off apart from one...

Last post

thanks, will give that a try, well worth knowing!

2 Replies

3520 Views

Last post by szhrr5cc
Tue Apr 05, 2022 10:46 pm
"Optimal" Spheres

Last post by DLM « Sat Apr 02, 2022 7:45 pm
Replies: 6
by DLM » Tue Mar 29, 2022 3:07 pm

First post

Saw a new name on the list of aftermarket manufacturers when when looking up a BX sphere part number - OPTIMAL

Don't think I'll be buying but does...

Last post

Thanks for all comments.

I did come across a post going back a way on the French Car Forum. It was essentially from a Pleiades man, and gave views...

6 Replies

5762 Views

Last post by DLM
Sat Apr 02, 2022 7:45 pm
Driveshaft removal tips welcome

Last post by rhysaccess « Sun Mar 27, 2022 9:43 am
Replies: 2
by rhysaccess » Sat Mar 26, 2022 11:43 am

First post

Howdy all,

Driveshaft removal (entirely), hasn't been as intuitive on the TZI as I'd hoped.

Its part of the engine/gearbox removal set of...

Last post

Turns out it was all pretty easy -probably did it in about the same it took me to type this post.

I just like to plan where possible, to save hours...

2 Replies

1317 Views

Last post by rhysaccess
Sun Mar 27, 2022 9:43 am
Looking at buying a 16V

Last post by Cresco750 « Wed Mar 23, 2022 1:22 am
Replies: 30
by Cresco750 » Tue Feb 01, 2022 1:10 am
1

2

3
First post

Hi all

First time posting here in a long time. I’ve owned a number of different Cits over the past fifteen years or so, including D’s, XM, CX, C5,...

Last post

As the OP of this thread I’d thought I’d better offer a follow up? I decided not to pursue the white 16V in question; a bit too much of a project for...
30 Replies

25838 Views

Last post by Cresco750
Wed Mar 23, 2022 1:22 am
Sensible tasks- while engine is out.

Last post by Jaba « Tue Mar 22, 2022 8:09 am
Replies: 8
by rhysaccess » Sun Mar 20, 2022 11:44 am

First post

Howdy all,

I'm removing the engine out of my (newly acquired) 1990 TZI - to facilitate replacing a broken gearbox.

While it's out, it's timely to...

Last post

Something else to consider is the sump gasket if there are signs of leakage and while you are there and doing the crankshaft seal the sealing strips...

8 Replies

3666 Views

Last post by Jaba
Tue Mar 22, 2022 8:09 am
Fitting new rear brake pads and discs BX 1.4 St Tropez

Last post by rutter123 « Mon Mar 14, 2022 11:15 am
Replies: 10
by szhrr5cc » Thu Mar 10, 2022 9:52 pm

First post

Carrying on with getting the BX in better shape today I removed the rear brake pads preparatory to fitting new discs as the current ones are very...

Last post

Agreed the rear bleed valves are sods for snapping and sods to get out if they do. Steel against alloy over a long time is never good.
A tap with a...

10 Replies

2480 Views

Last post by rutter123
Mon Mar 14, 2022 11:15 am
Anti roll bar bush availability 95635526

Last post by ghaddon1701 « Sun Mar 13, 2022 5:05 pm

by ghaddon1701 » Sun Mar 13, 2022 5:05 pm

Hi everyone,

Can anyone who has access to service Citroen tell me if anti roll bushes are still available from Citroen please? Part number is...

0 Replies

63293 Views

Last post by ghaddon1701
Sun Mar 13, 2022 5:05 pm
Light bulbs

Last post by szhrr5cc « Wed Mar 02, 2022 4:50 pm
Replies: 4
by szhrr5cc » Wed Mar 02, 2022 1:28 pm

First post

As part of the ongoing effort to improve my BX St Tropez I've been looking at the headlights. Two things,

1, on the offside the smaller bulb in the...

Last post

Thanks Gents, useful info on the bulb and I'll have a look at the relay idea, just checked the glass and, happily, that appears firmly in place! One...

4 Replies

2311 Views

Last post by szhrr5cc
Wed Mar 02, 2022 4:50 pm
Purflux fuel filter head

Last post by DLM « Mon Feb 21, 2022 11:02 pm
Replies: 3
by davidicraik » Mon Feb 21, 2022 6:07 pm

First post

Having intermittent starting problems due to air getting into the priming fuel filter head that I believe is a Purflux C180 .
Does anyone know where...

Last post

As said above, the diaphragms on Purlux filter units can be problematic - causing bad running, surges and worse. Have at least one of the units from...

3 Replies

4650 Views

Last post by DLM
Mon Feb 21, 2022 11:02 pm
Intermediate Height Question

Last post by Fumbler « Wed Feb 09, 2022 6:44 pm
Replies: 12
by Fumbler » Wed Jan 26, 2022 12:01 pm

First post

Since being fixed, the car raises and lowers to the proper height on every setting, apart from intermediate height. When I select this with the...

Last post

Issue was resolved by replacing a worn bronze bush in the rear height corrector lonkage. Everything on the suspension is now mechanically sound. The...

12 Replies

2433 Views

Last post by Fumbler
Wed Feb 09, 2022 6:44 pm
clutch change.

Last post by tim « Tue Feb 08, 2022 1:32 pm
Replies: 6
by tim » Wed Jan 19, 2022 1:14 pm

First post

Hi all - still here. The Red One (92 TXD diesel) has been OK barring 'sorting out things' as we do. However, a trip up London and back with a small...

Last post

Hi. The cable bracket is permanently fixed to the cradle by spot welds, as are the pedals - never meant to be removed. So I need a complete cradle....

6 Replies

4617 Views

Last post by tim
Tue Feb 08, 2022 1:32 pm
Fitting new front brake pads BX 1.4

Last post by DLM « Mon Feb 07, 2022 11:32 am
Replies: 8
by szhrr5cc » Fri Feb 04, 2022 7:31 pm

First post

MOT advisory to change the front pads....I have got the old ones off following the Haynes manual (I know..). I've been able to fit the new pads into...

Last post

I've experienced problems with aftermarket plates too from a kit - fairly similar in dimensions, but oversized. As you've found, normally the old...

8 Replies

4680 Views

Last post by DLM
Mon Feb 07, 2022 11:32 am
Burned resistor in my dashboard

Last post by oucham « Thu Feb 03, 2022 3:35 pm
Replies: 8
by oucham » Tue Feb 01, 2022 8:26 pm

First post

Dear friends.

There is a burned resistor in my car's dashboard. It was like that since I bought the car, so I do not know the reason. It is not...

Last post

Thanks a lot White exec [-o<

I will try to fix the dashboard

8 Replies

2401 Views

Last post by oucham
Thu Feb 03, 2022 3:35 pm
What is this device in my engine

Last post by oucham « Thu Feb 03, 2022 2:15 pm

by oucham » Thu Feb 03, 2022 2:15 pm

Hello.

Can someone tell me what is the name of this device in my engine, and what it does.

Three vacuum pipes are connected to it.

Thank you

0 Replies

62558 Views

Last post by oucham
Thu Feb 03, 2022 2:15 pm
Rocker clearance Citroen BX14RE, engine 150Y/XY6B

Last post by oucham « Tue Feb 01, 2022 9:34 pm
Replies: 2
by oucham » Tue Feb 01, 2022 6:31 pm

First post

Dear friends.

I need the values for rocker clearance for my engine. The Haynes book for my car lists the values only for the engines 150A and 150C....

Last post

Thank you for your reply.
Do you know if the clearance are the same for all 150 engines?

2 Replies

856 Views

Last post by oucham
Tue Feb 01, 2022 9:34 pm
Rear Brake Line Replacement

Last post by rutter123 « Sat Jan 29, 2022 9:43 pm
Replies: 26
by Dytie » Mon Jan 17, 2022 10:39 pm
1

2
First post

I recently acquired a mk1 16v project from a well known forum member who’s username rhymes with Hitch that I’m planning to restore. It needs...

Last post

A lot of the time it's just trial and error getting the rear end to work and behave itself after bleeding it down, usually just a case of a few lows...
26 Replies

32960 Views

Last post by rutter123
Sat Jan 29, 2022 9:43 pm
BX 16v cooling radiator

Last post by Kaapelimies « Wed Jan 26, 2022 3:08 pm
Replies: 8
by -=RAMZES=- » Mon Jan 24, 2022 9:31 pm

First post

Hi, to everybody.
I need new cooling radiator for my BX. As I know it's unique and was installed only in BX 16v. It's made of cooper, and have it's...

Last post

I think the original radiator is made out of brass, so it can be fixed by a professional, if it's not broken in an accident that is. In which case...

8 Replies

4602 Views

Last post by Kaapelimies
Wed Jan 26, 2022 3:08 pm
Instrument cluster bulb replacement

Last post by Jugostran « Sun Jan 16, 2022 11:01 pm
Replies: 7
by Jugostran » Fri Jan 14, 2022 9:23 pm

First post

Hello everyone,
This will be a short one. Several bulbs in my instrument cluster went out. I wanted to fix them, so I bought a 30 pack of T5 12V...

Last post

Good result! Apologies for the slip with the bulb spec....W1.2W is correct. Have corrected my post.
Glad it's now working.
To maximise instrument...

7 Replies

1114 Views

Last post by Jugostran
Sun Jan 16, 2022 11:01 pm
Citroen Service Box

Last post by bowei001 « Sat Jan 15, 2022 6:17 pm
Replies: 2
by bowei001 » Sat Jan 15, 2022 11:21 am

First post

Does anyone know whether Citroen Service Box contains information on a Mk1 BX and, If so, does it give part numbers ? I have an original microfiche...

Last post

Hi Chris,
Thanks for the information and the offer. I think that I'll register and log in for a short while and try a large download to look at...

2 Replies

1134 Views

Last post by bowei001
Sat Jan 15, 2022 6:17 pm
Diagnosing the door open warning display

Last post by Jugostran « Fri Jan 14, 2022 9:20 pm
Replies: 12
by Jugostran » Wed Oct 27, 2021 11:20 pm

First post

Hello everyone!
So, I have been tinkering with the door open display, and I am currently stuck in a diagnostics mess. I have determined that the...

Last post

The best thing that you can do is find the white connecter behind the glove box and start diagnostics from there.

The pins need to be earthed out to...

12 Replies

1817 Views

Last post by Jugostran
Fri Jan 14, 2022 9:20 pm
RH drive shaft intermediate bearing

Last post by white exec « Fri Jan 07, 2022 7:35 pm
Replies: 15
by white exec » Sat Jan 01, 2022 3:51 pm
1

2
First post

Have come up against a full-stop on this one - hopefully someone can help...

19D driveshafts - replacement
LH shaft came out ok, and have inserted...

Last post

Just as a postscript re: the gear whine . . .

The 5th gear whine (at 110-120km/h) from last year was all but eliminated with the addition of a 125ml...
15 Replies

8297 Views

Last post by white exec
Fri Jan 07, 2022 7:35 pm
Front Bumper Mounts

Last post by white exec « Fri Dec 24, 2021 8:20 am
Replies: 5
by krekov » Thu Dec 23, 2021 6:14 pm

First post

Hello,
I got a new front bumper and upon mounting I realized I couldn't get it to not sag a bit, even though it was mounted properly on the plastic...

Last post

A single 4mm hole (vertically through the horizontal metal wing and plastic bumper flanges) allows a cable tie to securely lift the bumber into its...

5 Replies

1119 Views

Last post by white exec
Fri Dec 24, 2021 8:20 am
BX16 auto box oil cooler

Last post by bowei001 « Sun Dec 19, 2021 1:53 pm
Replies: 10
by bowei001 » Sun Nov 21, 2021 10:56 am

First post

I had to take my autobox oil cooler off to see if it was leaking (turns out it wasn't!) and I need the 2 oil seals to put it back. I don't fancy...

Last post

I fitted the cooler today. Then I torqued it up I found that the cooler would rotate rather that clamp rigidly. Obviously this would allow leakage so...

10 Replies

2867 Views

Last post by bowei001
Sun Dec 19, 2021 1:53 pm
Xud7te rebuild

Last post by Xm25td « Wed Dec 15, 2021 5:37 pm
Replies: 11
by Xm25td » Sat Dec 11, 2021 9:49 pm

First post

Hi all,
I have a citroen bx tzd turbo that skipped timing and broke camshaft in 3 pieces and camshaft bearings couldnt find a replacament head so i...

Last post

Are all xud heads the same (oval ports), can i fit pulley for hydraulic pump on every head and cam?
Are there any differences between 1.7 1.7 td,...

11 Replies

4542 Views

Last post by Xm25td
Wed Dec 15, 2021 5:37 pm
Drive shaft replacement

Last post by white exec « Tue Dec 07, 2021 5:48 pm
Replies: 2
by white exec » Tue Dec 07, 2021 11:48 am

First post

Both shafts on the 19D are knocking still, even after injecting fresh grease.
The r.h. outboard bellows has a small split, and has thrown grease out,...

Last post

Finally found it...
BX_D_nonABS_driveshaftsupportbrg.JPG
3247 03 and associated bits (#6, 10, 7).

2 Replies

2573 Views

Last post by white exec
Tue Dec 07, 2021 5:48 pm
Oil temp gauge, on 19D

Last post by Kaapelimies « Fri Dec 03, 2021 3:30 pm
Replies: 10
by white exec » Sun Nov 14, 2021 11:14 am

First post

Oil and coolant temp gauges now fitted to the 19D.
Coolant temp gauge AOK, and good to be able to watch thermostat and cooling fans doing their...

Last post

In my experience for the oil temperature gauge to reach 100C you needs to be doing illegal speeds for a prolonged period :D

Or visit Germany.. The...

10 Replies

5092 Views

Last post by Kaapelimies
Fri Dec 03, 2021 3:30 pm
Driveshafts

Last post by davidicraik « Tue Nov 30, 2021 11:16 am
Replies: 5
by davidicraik » Fri Nov 26, 2021 3:57 pm

First post

I am trying to source new left and right side driveshafts for my 1990 BX tzd (90hp). I need the non - abs version.
Any recommendations for supplier?

Last post

That's brilliant,
Thank you Chris

5 Replies

941 Views

Last post by davidicraik
Tue Nov 30, 2021 11:16 am
Rear end not raising.

Last post by white exec « Fri Nov 26, 2021 7:38 pm
Replies: 6
by ????? » Wed Nov 24, 2021 7:22 pm

First post

After 6 months on stands with no rear subframe, Last week my BX finally was partially reassembled and had LHM flow through its veins again. It even...

Last post

Re: the missing exhaust tailbox hanger, I've had to deal with just that a month or so ago, where the body-welded rod hook had detached from the...

6 Replies

1307 Views

Last post by white exec
Fri Nov 26, 2021 7:38 pm
E10 petrol

Last post by Fumbler « Tue Nov 23, 2021 11:07 am
Replies: 12
by deltic » Tue Nov 09, 2021 8:40 pm

First post

Apologies if this is has been discussed on here previously, but my guess is that under normal circumstances we shouldn't be using E10 petrol in any...

Last post

On a somewhat related topic the carb on my BX 16 TGS has a label 'E10'.

Is this just coincidence or were Citroen ahead of the game in 1992 and...

12 Replies

2773 Views

Last post by Fumbler
Tue Nov 23, 2021 11:07 am
BX 16 TGS 1992 Estate -> Front Wiper Motor (Valeo # 535 37 702)

Last post by Routemaster « Sun Nov 21, 2021 9:31 pm

by Routemaster » Sun Nov 21, 2021 9:31 pm

Any leads for sourcing a replacement front wiper motor gratefully received.

Looking for a 'sensibly priced' replacement that isn't going to be...

0 Replies

62216 Views

Last post by Routemaster
Sun Nov 21, 2021 9:31 pm
BX 16v Thermostat

Last post by white exec « Tue Nov 16, 2021 7:28 am
Replies: 29
by krekov » Thu Oct 28, 2021 6:35 pm
1

2
First post

Hello,
I've swapped the thermostat on my 16v due to unresolved overheating when standing still (everything else checked many times over). The old one...

Last post

:D What you say is correct, Krek. When the IGN is switched on, the temp gauge needles rise from their rest positions to a slightly higher position,...
29 Replies

3788 Views

Last post by white exec
Tue Nov 16, 2021 7:28 am
Adjusting ride height on normal suspension setting

Last post by Jaba « Fri Nov 12, 2021 10:01 am
Replies: 10
by Jugostran » Mon Nov 08, 2021 4:33 pm

First post

Hey there,
I have been reading through some old threads regarding this topic, and found out that my BX rides a bit too high on its normal suspension...

Last post

Leaking LHM reservoir: is this from the underneath if so it will have rusted through. The rust holes can be repaired with ingenuity but sourcing a...

10 Replies

19675 Views

Last post by Jaba
Fri Nov 12, 2021 10:01 am
BX Suspension Spheres - Citroen's full spec

Last post by Jaba « Thu Nov 11, 2021 11:36 am
Replies: 7
by white exec » Sun May 02, 2021 2:24 pm

First post

Lots of discussion about where to buy replacement spheres, and what the full and correct spec for each sphere, on each model, is.

This is Citroen's...

Last post

Hi Richard, Actually I missed that you missed my reply.
Obviously size matters and that was not what I meant when I said I don't think it too...

7 Replies

1872 Views

Last post by Jaba
Thu Nov 11, 2021 11:36 am
Return pipe rubber elbow - 5280 P5

Last post by Kaapelimies « Tue Nov 09, 2021 9:12 pm
Replies: 2
by white exec » Tue Nov 09, 2021 8:35 am

First post

Lots of us have had the rubber elbow (height correctors and other locations) split or perish.
Part no. is 5280 P5 Hydraulic return tube sleeve,...

Last post

Thanks for this Xantia-spares info! Their english is quite horrible and pictures are bad, but some rubber parts are worth a try at their price to...

2 Replies

2915 Views

Last post by Kaapelimies
Tue Nov 09, 2021 9:12 pm

New Topic

4931 topics

Page 2 of 99
- Jump to page:
Previous
1
2
3
4
5
…
99
Next

Return to Board Index

Forum permissions

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum