As posted elsewhere I recently had a stainless steel exhaust system fitted to the BX which unfortunately I find uncomfortably noisy. Indeed it is...
Last post
I've been persevering with mine & I've realised that if I keep the engine revs down, keep the back seats up & if the radio is on, then I can't really...
Hi all, been trying to find out whether the engine in my 1986 BX16TRS is interference or non-interference? None of the web refs I Googled show...
Last post
Correct me if I'm wrong, years ago I had a mk1 vauxhall astra 1300 cambelt snapped due to seized water pump
No valve or cam damage, new belt and pump...
While checking valve clearances on my DKZ engine, I've used the 159 specs in one of my Haynes manuals of 0.15 - 0.25 Inlet & 0.35 - 0.45...
Last post
Yes, the vagaries of chasing down some exact numbers by shimming are not new to me. If I’m to use the “standard” BX19 clearances – just three exhaust...
Hello All, working on our 16v to remove the alternator as it very noisy and either needs replacing or rebuilding. We have freed it off apart from one...
First time posting here in a long time. I’ve owned a number of different Cits over the past fifteen years or so, including D’s, XM, CX, C5,...
Last post
As the OP of this thread I’d thought I’d better offer a follow up? I decided not to pursue the white 16V in question; a bit too much of a project for...
I'm removing the engine out of my (newly acquired) 1990 TZI - to facilitate replacing a broken gearbox.
While it's out, it's timely to...
Last post
Something else to consider is the sump gasket if there are signs of leakage and while you are there and doing the crankshaft seal the sealing strips...
As part of the ongoing effort to improve my BX St Tropez I've been looking at the headlights. Two things,
1, on the offside the smaller bulb in the...
Last post
Thanks Gents, useful info on the bulb and I'll have a look at the relay idea, just checked the glass and, happily, that appears firmly in place! One...
Having intermittent starting problems due to air getting into the priming fuel filter head that I believe is a Purflux C180 .
Does anyone know where...
Last post
As said above, the diaphragms on Purlux filter units can be problematic - causing bad running, surges and worse. Have at least one of the units from...
Since being fixed, the car raises and lowers to the proper height on every setting, apart from intermediate height. When I select this with the...
Last post
Issue was resolved by replacing a worn bronze bush in the rear height corrector lonkage. Everything on the suspension is now mechanically sound. The...
MOT advisory to change the front pads....I have got the old ones off following the Haynes manual (I know..). I've been able to fit the new pads into...
Last post
I've experienced problems with aftermarket plates too from a kit - fairly similar in dimensions, but oversized. As you've found, normally the old...
I recently acquired a mk1 16v project from a well known forum member who’s username rhymes with Hitch that I’m planning to restore. It needs...
Last post
A lot of the time it's just trial and error getting the rear end to work and behave itself after bleeding it down, usually just a case of a few lows...
I had to take my autobox oil cooler off to see if it was leaking (turns out it wasn't!) and I need the 2 oil seals to put it back. I don't fancy...
Last post
I fitted the cooler today. Then I torqued it up I found that the cooler would rotate rather that clamp rigidly. Obviously this would allow leakage so...
Both shafts on the 19D are knocking still, even after injecting fresh grease.
The r.h. outboard bellows has a small split, and has thrown grease out,...
Last post
Finally found it...
BX_D_nonABS_driveshaftsupportbrg.JPG
3247 03 and associated bits (#6, 10, 7).
Hello,
I've swapped the thermostat on my 16v due to unresolved overheating when standing still (everything else checked many times over). The old one...
Last post
:D What you say is correct, Krek. When the IGN is switched on, the temp gauge needles rise from their rest positions to a slightly higher position,...
Hey there,
I have been reading through some old threads regarding this topic, and found out that my BX rides a bit too high on its normal suspension...
Last post
Leaking LHM reservoir: is this from the underneath if so it will have rusted through. The rust holes can be repaired with ingenuity but sourcing a...
Hi,
I have just replaced the rear brake pipes with some I bought from another citroen enthusiast, about 10 years ago.
I have never had any problems...
Last post
Good result.
Those sleeved joints are extraordinarily good at handling exteremely high pressures, provided that everything lines up, and the pipe end...
My bx.1.9d has been off the road for a while for extensive maintenance. I had problems getting it started and i have found that there...
Last post
I have temporary bypassed the original filter assembly to remove it out of the equation, the electric pump is now the primer. once primed the pump is...
I've removed the wheels on my BX once, to have them powder-coated. Now they're back on, but dang if I can find the torque spec. anywhere. Not in...
Last post
Thanks! Found it in the old (brown cover) Haynes, but the newer version (blue cover) has different Chapter names - it's under Ch. 11, Suspension and...
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum