I'm getting to the point now with my BX restoration project that it is nearly ready for the road. It would already be on the road apart from a couple...
Last post
I have several headlamp stalk switches if you need one all good and fully working. £15 posted. I also have heater several heater control panels.
Are they all the same for petrol BXs, or do I need a specific one for a 16v? Mine must be bust because on the motorway the temp's barely above 65-70...
Last post
Yes that's what I thought, mine is obviously stuck open all the time.
I am new on here and this is my first petrol BX here in the UK. Had a diesel one in France many years ago.
My problem is the car stinks of...
Last post
You might want to check out the seal on the fuel level sender unit. This is accessible under the rear seat. I've had problems with my series 2 giving...
I've had my TZD for 6 months now and loving every minute of her.
I had the spheres and LHM changed shortly after buying the car as the old ones were...
Last post
Lots of good information here and on related pages:
Just putting this out there to anyone with definitive knowledge.
On the front of the injection manifold, 1600 single point injector (what would be...
Last post
The 1.6i was the only UK 1.6 petrol version of the injection model AFAIK and started in either very, very late 91 or early 92. There is at least one...
Basically the TXD sprung a leak where the pipe that goes to the Oil filter cooler rubbed against the starter motor! Tracing the pipe back it goes to...
Last post
I use silicone, the high temperature variety, for either gaskets or flues.
After I read this I remembered there was a tube of instant gasket laying...
Hi guys, I need to replace the front most wishbone bushes on the front arms of my 1991 TZD. I've seen some on Ebay which say they are the equivalent...
Last post
From memory (I did a batch of them a while back) it's actually easier to do them with a big vice - I've got a press and it's hard to get it all lined...
hey guys, one of the things i have been toying with on my old fiats is fitting a small 5kw auxiliary heater in the coolant system, ive not done it as...
Last post
Wouldn't it be simpler if you want to do this to use the heater that Ford use on diesel that heat by glowplugs?
Hello all, I have always fancied in the long run (as in in the next 5 years or so) putting BX Sport twin carbs and associated inlet manifold and air...
Last post
I think the issues with the fit on RHD cars was the exhaust manifold fouling the steering rack etc, from my research the carbs should just bolt on -...
I have central locking activated off the key/doors but no plipper on my recently acquired TZi estate. I have found a circuit board loose in the roof...
Last post
Thank you both for the advice. I may take you up on your offer Jaba re the plipper etc and see if I can get it working. In the meantime I'll have a...
Hi
Finally been able to log on, fab.
Bought a metallic grey 1990 Citroen BX 1580cc Millesime from my neighbour in France,he has just given up driving...
Last post
Thanks re spec of car, so what does an Athena have or have not, where does it fit in, looks quite sporty with spoiler and seats are quite smart too.
I need to change the exhaust on my 89 19tri auto estate (yes, on the road continuously from new, whatever it says on How many left ). The front pipe...
Last post
Won't make much difference. It's just a little silencer, and plenty of 1.9 cars came without them. The exhaust may be very slightly fruitier without...
I have found today when loading logs into my van its possible to load it so much the suspension does not rise properly! I have never managed to do...
Last post
You could calculate the approximate max load by comparing the distance between high and low position of the suspension to the travelling distance of...
Should they both come on together? I have mine set to cut in at approx 88/90 degrees c, but only one cuts in on the offside. They both work with a...
Last post
For time being i have left it with just one fan working on the rad switch and fitted a manual override on the second, sat in traffic last week for a...
Hi All. I have a recurrent problem with my GTI 8v - when it's been left for a couple of weeks, it starts first time and then is a bit juddery when it...
Last post
There are a few things that can cause this, bx's with fuel injection hate any type of air leaks pre throttle body even the tiniest leak will cause...
For the last 3 weeks I've had a flickering battery light (at first it would go off after a while), but strangely no starting issues as yet (powerpack...
Last post
Alternator arrived this morning, but it seems that Peugeot 406 alternators aren't all compatible after all - the 2 mounts at the bottom are too close...
Hi all, I have recently acquired an air conditioning system for my BX. Already I have a few questions on how to put it all in.
The car is all in...
Last post
a lot of this i am going to have to go through with the changing of seals and swapping of compressor oil.. thankfully i have manifold gauges and a 2...
Just of lately this week my 2008 LWB Relay van has developed an intermmitent prob with the PAS, the steering stiffens up occasionally then on turning...
Last post
Mine is defo pump driven as there is a PAS pump ( belt driven) on the bottom left hand side of the engine, i suspect i may have 2 separate issues...
Hi
I'm just putting a new clutch in a BX 19TRS and am not sure how much to torque up the six 13 mm bolts holding the pressure plate to the flywheel....
Last post
Like most tools from Poundland-they are made from bread and butter.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
